Capitol Improvements

Michigan State Capitol

NUCA Associate Member Aids in Michigan State House Renovation

When your state’s Capitol Building is almost 150 years old, it’s going to require constant renovation and modern upgrades. This is true for Michigan’s Capitol in Lansing, which has been renovated many times since its original construction in 1872. That includes, of course, the renovation of the beautiful architecture in the building, which the public can see and enjoy. But it also requires the modernization of the building’s almost 150-years-old plumbing.

It is the out-of-the-way, behind-the-walls, and under-the-building renovation that can be most challenging for renovation contractors. For example, Hoffman Bros. Inc.—headquartered in Battle Creek, Michigan—was recently tasked with preparing a section of the Capitol’s sanitation system for sliplining, including sections of original pipe.

The installation of the new cured-in-place resin pipe lining required three excavations: a feeder hole, an alignment hole, and a draw hole for the winch to pull the lining through the pipe. Hoffman started the excavation project by digging an easy 2-ft deep feeder hole on the north end of the Capitol grounds outside the building. However, it was the second and third excavations under the Capitol that was anything but easy.

“Both the alignment and draw holes needed to be dug in a 5-ft crawl space with pipes and conduits running everywhere,” said Aaron Mast, Hoffman’s Superintendent. “Once we were in the correct spot in the crawl space for the alignment hole, we had to dig an 8-ft deep hole, which was partly under a conduit 2-ft off the floor.”

Trench Production System

Making matters even more challenging was that the hand-dug “excavations” were deeper than 5 ft, which MIOSHA stipulates must employ one of the three approved trench protection systems: sloping, shielding, or shoring. Mast needed help finding a workable shoring solution, so he turned to the specialists at NUCA Associate Member Efficiency Production, one of the nation’s leading trench shielding and shoring manufacturers, and conveniently headquartered 20 miles south of Lansing in Mason, Michigan.

“We’ve dealt with Efficiency on a lot of different excavation projects in the past, some using trench shields, some with Slide Rail Systems,” said Mast. “So I called (Efficiency’s Michigan Sales and Rental Manager) Jim Hamilton, because I knew neither trench boxes nor Slide Rail was going to work for this project,” Mast added.

“When I came out to the Capitol and saw where the Hoffman guys were digging; under the building in a crawl space where you couldn’t even stand up straight in most spots; I knew that the best thing—really the only thing—that would work for trench protection was hydraulic shores,” Hamilton said.

Hydraulic Shores

Hydraulic vertical shores consist of a pair of strong 8-in. aluminum rails that are connected by hydraulic cylinders. The hydraulic cylinders are pressurized outside of the excavation with a hand-pump. Where trench shields are used to protect workers against cave-ins, hydraulic shores are used to actually apply pressure to trench walls to prevent cave-ins; a critical consideration for shoring the 4- x 6-ft pits in the tight space directly below the Capitol’s famous Rotunda.

“Another thing that made hydraulic shores the only thing that would work was that all equipment needed to go down a 2-ft square access hatch to reach the utilities under the Capitol,” Hamilton continued. “The Shores, plus pump bucket and tools, needed to be carried down the access ladder by hand,” exclaimed Hamilton.

Hand-dug Excavations

Of the two hand-dug excavations under the Capitol, the alignment hole was about 8- to 9-ft deep, but there was only 4- to 4.5-ft of overhead space. The second hole for the winch was 6-ft deep and dug with only 4- to 5-ft of overhead space. To shore the pits, Hoffman employed 8 single-cylinder hydraulic “spot-shores,” 4 running in each direction. When activated, the hydraulic pressure from the cylinders prevents the trench walls from collapsing.

“I hadn’t ever heard of hydraulic shores before Jim explained how they worked; and sure enough, they were slick and did the job,” Mast said. “We have a lot of traditional Efficiency trench safety equipment in our fleet, but I wouldn’t hesitate to use hydraulic shores again if we encounter a problem that can’t be addressed by something we already have in our toolbox,” Mast concluded.

Established in 1947, Hoffman Bros., Inc. is a fourth-generation, family-owned business. Headquartered in Battle Creek, Michigan, Hoffman Bros. specializes in underground construction, road and highway construction, and site development. Today Hoffman Bros. employs over 190 workers and owns over 200 pieces of heavy equipment. Learn more at www.hoffmanbrosinc.com.

Efficiency Production, an Arcosa Shoring Products company, provides versatile trench shielding and shoring systems. For more information, visit www.efficiencyproduction.com.

James McRay is Director of Marketing & Media for Efficiency Production, An Arcosa Shoring Products Company.

0

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.